J&J Truck Bodies and Trailers : Product Line : Trailers : DynaHauler DT


	Dump Bodies Trailers Specialty In-Stock New & Used Distributors
	AF APO AT DT FL FLT FTA FTS HRT LF PTA SPO SST Smooth Sides

Take a look at all of our dump trailers.

DEMOLITION DUMP TRAILER
The DYNA^HAULER/DT dump trailer is built to work in abusive job-site conditions hauling heavy demolition and construction debris. It's constructed of top grade materials like 3/16" HARDOX® 450, 175,000 PSI minimum yield, and abrasion resistant steel side panels. The floor is 5/16" HARDOX® 450 plate, 175,000 PSI. With standard specs like these, you can depend on this workhorse for many years of hard hauling work.

There's no substitute for a trailer built by the experts at J&J Truck Bodies & Trailers. We don't cut corners and we don't compromise on quality. Rely on our 40+ years of experience to build you the dump trailer you want - we'll build it to your specification and application.

S T A N D A R D S T E E L S P E C I F I C A T I O N S :
Lengths
	24' to 40'
Side height
	54' to 72'
Overall height
	Variable (13'6" maximum available)
Gate height
	54' to 72'
Tire to end of floor
	4"
King pin to front of trailer
	18" (others available)
King pin to center of suspension
	Variable, consult your J&J representative
Center of hinge pin to end of floor
	6"
Side panels
	Abrasion resistant 3/16" HARDOX® 450 (175,000 lb. PSI minimum yield) steel with one (1) row of Horizontal side brace posts (centered).
Bulkhead
	Abrasion resistant 3/16" HARDOX® 450 (175,000 lb. PSI minimum yield )steel.
Dog box
	Abrasion resistant 3/16" HARDOX® 450 (175,000 PSI minimum yield) steel with angle reinforcements corners.
Floor
	Abrasion resistant 5/16" HARDOX® 450� (175,000 PSI minimum yield) steel. Solid welded with radius corners.
Bottom & Top Rail
	_" formed high-tensile bottom rail. Top rail is 4" x 4" x _" A-500 structural tubing with inverted dirt shedding angle on top.
Side & Rear Posts
	Vertical side posts on 24" centers. Rear posts are 4" x 4" x _" A-500 tubing welded and gusseted to rear crossmember under floor, then reinforced with 12" x 4" formed section.
Understructure
	4" I-beam crossmembers (7.7 lb./ ft.) on 12" centers. Longitudinals are 6" x 6" x 3/8" angle running full length, welded to all crossmembers and gusseted to every other crossmember.
Tailgate
	1/4" Abrasion resistant HARDOX® 450 (175,000 lb PSI minimum yield) steel ,9 panel, barn door type, curbside hinge, driver's side rear positive latching mechanism.
Lighting
	Truck-Lite� sealed and shock proof system.
Axles
	Dana� D22, 25,000 lb., 5" round.
Brakes
	16 _" x 7"x _" air operated, with ABS 4S2M system
Frame
	16" deep, wide flange beam (31 lb./ft.) high-tensile steel.
Hoist
	A variety of front mounted hoists are available, sized to fit body length and Payload requirements
Suspension
	60,000 lb., single point.
King Pin
	Holland Mark V, 2-speed, with sand pads 180,000 lb. static load capacity.
Landing Gear
	Holland T809 2 7/8" diameter. King pin plate is 3/8" A-36 steel.
Wheels
	24.5 x 8.25 steel hub pilot.
Tires
	11R24.5, 14 ply.
Other standard features
	Mud guards & mud flaps; Steps; Shovel hangers; Tarp Bars; ABS brakes

P O P U L A R S T E E L O P T I O N S :
Side Panels
	A variety of heights and thicknesses are available. Extra Horizontal side braces.
Floors
	_" or 3/8" HARDOX®.
Tailgates
	Top hinge air operated, three way with ground level manual control, and water tight gates.
Tarping
	Tarps, tarp bows, and tarp baskets. Manual or electric: slide, arm, or roll tarpers.
Other
	Heat; Tire carrier; Steerable, non-steerable, and standard lift axles ; Catwalk/ladders; Tool box ; Spreader Apron ( maximum of 7" long); Coal door ; On-board scales; Fenders ; Vibrators; Centrifuse hubs; Self-Contained power units; Extra Heavy-duty push bumper . L.E.D. Lighting.

Standard specifications may vary according to customer preferences and requirements. At J&J, we custom build to suit your needs. Licensed under U.S. Patent No. 5,454,620.